|
|
Jarz Performance Machine
Shop Services |
 |
|
We are
your source for fuel injection tuning. Don't waste
your money. Why settle for less power? Do it
right the first time with Jarz Performance
engine packages: money well spent
guaranteed!! Let us help with our 12 years of Dyno
tuning experience. Get more power, fuel economy,
less emissions, safer cooler running motor. Let
our professionally trained technicians tune your big
twin Sportster, Buell or V Rod.
|
|
Cylinder
Head Porting | EVO
Big Twin Kits | Twin Cam Kits
| Dyno Room |
|
|
|
|
|
|
Back Cut Gear Services
For 5 Speed Transmission
High RPM Shifting will
be greatly improved with this service. No
more missed shifts, smoother shift action.
All gears are inspected for wear. Engagement
dogs are back-cut on our precision jig.
Price: $225.00 |
|
|
|
|
|
Compression Releases Installed
Raising the
compression on any big twin will put greater
demand on the starting system and reduce the life
of your starter clutch. Installing these
little units will save your starter clutch and
ring gear. It is less expensive to have
these installed while the heads are off than to
replace your starter clutch! Heads are
machined for compression releases on our
bridgeport milling machine.
Price: $150.00 for machining
$100.00 Releases
|
Timken Upgrade for 2003
Call for Pricing
|
Crankcase Boring
EVO. Cases can
be bored for up to 3-13/16" cylinders.
Twin cam can be bored for up to 4-1/8".
Additional charge to bolt together, torque and
remove cylinder studs.
Price: $200.00
|
|
|
|
|
|
Machine EVO Cylinder Bases
This service will
true warped or gouged cylinder base surface to
help reduce leakage. Also easily removes
stubborn base gaskets. Great way to adjust cyl.
deck height.
Price: $50.00
|
Fuel Injection Custom
Mapping
The only way to
properly dial in your fuelie is to run it up on
the dyno and check the emissions at different
loads and RPMS. We can remap your stock ECM
using direct link or most any other system you may
already have.
Price: $100.00 per hour |
Dyno Tuning
On our Dyno Jet 250i
load control dyno with exhaust gas
analyzer. Give your ride the tune up it
deserves and extract the horsepower you paid
for. Our experience and thousands of dyno
runs in our data base will assure you that every
last bit of power is found
Price: $ 100.00 per hour
or $50.00 for 3 pulls.
|
|
|
|
|
|
Bore and Hone T.C.
Cylinder 's
To 3-7/8" for
95". This is a cost saving alternative
to replacing your cylinders.
Price: $300.00
|
Install 66 Tooth Ring Gear
High compression and
big inch motors installed in 1994 and later big
twins will benefit by upgrading the weak 102 tooth
for the much stronger 66 tooth ring gear.
Stock gear is removed from clutch shell using mill
to cut rivets and new gear installed.
Price: $75.00 Labour Only
|
Shave Cylinder Heads
Heads are cut on our
lathe to desired chamber volume. Give us
your bore, stroke, and piston dome volume.
We will calculate your compression ratio.
Price: $100.00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
c |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
